If I execute: journalctl -xe I get the following output:Īpr 09 11:43:33 meet turnserver: 0: turn server id=2 createdĪpr 09 11:43:33 meet turnserver: 0: turn server id=0 createdĪpr 09 11:43:33 meet turnserver: 0: turn server id=4 createdĪpr 09 11:43:33 meet turnserver: 0: turn server id=3 createdĪpr 09 11:43:33 meet turnserver: 0: IO method (general relay thread): epoll (with changelist)Īpr 09 11:43:33 meet turnserver: 0: turn server id=1 createdĪpr 09 11:43:33 meet turnserver: 0: turn server id=5 createdĪpr 09 11:43:33 meet turnserver: 0: IPv4. Invoke-rc.d: initscript nginx, action “reload” failed. See “systemctl status rvice” and “journalctl -xe” for details. Job for rvice failed because the control process exited with error code. In a previous Installation I remember that the setup did ask for a passphrase to setup the SSL Cert, but that didn’t happen. In a further step the setup asks to put the *.crt file and the *.key file in the /etc/SSL directory what I did. In the step where the setup asks about the SSL Cert I did choose to use my own SSL Cert. Package jitsi-meet-web-config is not configured yet.ĭpkg: error processing package jitsi-meet (–configure):ĭependency problems - leaving unconfiguredĮrrors were encountered while processing:Īfter I couldn’t find the error in any of the configuration files with nginx, I’ve decided to setup a new ubuntu Server and begin with a new jitsi-meet installation from scratch. Jitsi-meet depends on jitsi-meet-web-config (= -1) however: No apport report written because the error message indicates it’s a follow-up error from a previous failure.ĭpkg: dependency problems prevent configuration of jitsi-meet: Installed jitsi-meet-web-config package post-installation script subprocess returned error exit status 1 Use ‘sudo apt autoremove’ to remove them.Ġ to upgrade, 0 to newly install, 0 to remove and 8 not to upgrade.Īfter this operation, 0 B of additional disk space will be used.ĭpkg: error processing package jitsi-meet-web-config (–configure): Libtimezonemap-data libtimezonemap1 linux-oem-headers-4.15.0-1043 Libdmraid1.0.0.rc16 libfwup1 libido3-0.1-0 libllvm6.0 libllvm7 libllvm8 Icedtea-netx-common kpartx kpartx-boot libdbusmenu-gtk4 libdebian-installer4 The following packages were automatically installed and are no longer required:Īpt-clone archdetect-deb btrfs-tools cryptsetup-bin dmraid Am I supposed to run Jitsi Meet from within my Browser? I thought that this would give a standalone app in Ubuntu 18.04 but it didn’t. “The best thing you should do is: launch 2 times the purge command, install nginx, install again jitsi-meet, if something doesn’t work (you can check by doina meeting with a room with youself), check the errors log, if you see a java exception it’s turnserver that collide with nginx 443 port (in that case purge just jitsi-turnserver)” Perhaps that’s good as later RubensRainelli stated: I noted that nginx is installed but not apache2. Not copying any file from skel directory into it.Īlso, jitsi-turnserver was not installed. Useradd: warning: the home directory already exists. I did apt-get remove -purge jitsi-meet jitsi-meet-prosody jitsi-meet-web-config jitsi-meet-web jicofo jitsi-videobridge, followed by sudo apt-get update, followed by apt install -no-install-recommends jitsi-meet. Trigger für ca-certificates (20180409) werden verarbeitet …Į: Sub-process /usr/bin/dpkg returned an error code (1)Īpt install -no-install-recommends jitsi-meet Trigger für man-db (2.8.3-2ubuntu0.1) werden verarbeitet … Trigger für systemd (237-3ubuntu10.39) werden verarbeitet … Installed jitsi-meet-turnserver package post-installation script subprocess returned error exit status 9 Jitsi-meet-turnserver (-1) wird eingerichtet …ĭpkg: Fehler beim Bearbeiten des Paketes jitsi-meet-turnserver (–configure): But everytime it failes with the following package: jitsi-meet-turnserver
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |